Home > Blue Screen > BSOD's And Comp Wont Boot With 8gig Ram Anymore

BSOD's And Comp Wont Boot With 8gig Ram Anymore

Contents

Since I used Windows Restore, my computer hasn't had one BSOD (yet). But I'm not being told that checking your Video Card is a good idea to isolate this type of a BSOD. it flashed and the sys reboot that is it , now it only use 4gb of ram , not 8 after i upgraded the OS (vista home-vista ultimate-7 ultimate 64 -7 As a guest, you can browse and view the various discussions in the forums, but can not create a new topic or reply to an existing one unless you are logged weblink

Stick works in another machine. –isarandi Aug 2 '14 at 19:37 It certainly sounds suspiciously like a compatibility problem. i guess i will need to buy new one..your hub-pages is very helpful... As you have tested your ram and found it to be going bad I think that replacements of same size and speed would have very high likely hood of solving your when i turn on i heard 3 beeps..

Blue Screen After Installing New Ram

O I also upgraded to windows 7 professional durring all this. How can i stop this i have 3gig of ram windows 7 with 55gig ssd nvd drivers all up to date.did complete clean . This is the closest I could find, but it's a CL5S. Adebayo Adeolu Ibrahim3 years ago What a great article!

Try testing each memory module in each of the memory slots to find if one of the slots is faulty. I am running the following config and really do need the 8gb and ultimate x64;   Hardware: Mb: Asus P5B Premium Ram: 4 x DDR 2 667mhz 2gb CPU: Intel quad CPT Gray WolfJan 25, 2014, 2:37 AM johnbl said: old BIOS are not too smart when I comes to adding new memory. Irql_not_less_or_equal Ram Upgrade I cannot even get the PC to boot now with 4 sticks fitted so i canot try this.

The screen goes blank after an external display device that is connected to the computer is turned off. Its an MSI K9A2 Platinum, not an ASUS.   I checked the voltage on the RAM when I first got it, because I was planning on tweaking it. You need to reset the virtual ram as well . Everything went well until Windows tried to load and blue screen.

Also i think the USB and MB Chipset use the same power supply as the DIMM's so if you have loads of periferals this could be a drain too My problem Windows Memory Diagnostic If it is quite a recent one, then chances are 300W aren't going to be enough to power that and all the other components in your computer. Back to top Page 1 of 2 1 2 Next Back to Windows Crashes, BSOD, and Hangs Help and Support 0 user(s) are reading this topic 0 members, 0 guests, 0 Removing the side cover and unplugging a module is not a big deal.

New Ram Blue Screen Error

However, my board has on board graphics as well, so I removed the graphics card and attached my monitor to the mainboard video output. http://newwikipost.org/topic/eVFHpaKmU8ToVw8iwmOeUkKVdR5ngTqS/Comp-wont-boot-after-CPU-swap.html Note that I removed many of the other components to make the memory more visible. Blue Screen After Installing New Ram So I kept pushing my voltage up a little more and when I went two settings higher on the voltage, Vista x64 booted like a pro and 8GB of ram working Blue Screen After Upgrading Ram The system is fine with the old RAM.

The machine restarted and then it just hung on the raid load screen. http://ixpix.net/blue-screen/bsod-when-on-boot.html I tried different memory timings, voltage etc. Its starting and with in 2 seconds its getting turn off.. finally it also failed. Ram Blue Screen Fix

boot laptop memory bsod share|improve this question edited Aug 2 '14 at 21:41 asked Aug 2 '14 at 19:08 isarandi 10614 2 I definitely would recommend running at least one Just posted Part 1, Part 2 will be out in a week.Is My PC dead?I've waited 27 years to have enough money to buy a good gaming build. If your memory is a weak point, either due to a fault or just having too little, your computer may slow down.If your computer becomes slower as the day goes on, check over here I hope I can get some help with this; http://www.newegg.com/Product/Product.aspx?Item=N82E16820231121 I remember buying the sticks indivigually, rather than a kit.

but it didn't help.  So I went and switched my memory modules to ADATA DDR2 800MHz (2GB x 4). Memtest86 Thanks to all who contributed. 0 Discussion Starter jkoll 8 Years Ago Well it turns out it was indeed the Mobo. He suggested the following.   The RAM i am using is the Geil Black Dragon PC6300 Quad Kit.

RAM Slot LeversThe levers for the memory slot are white in this example.

Here are example links in ebay- http://www.ebay.com/itm/CORSAIR-XMS2-4GB-2-x-2GB-240-Pin-DDR2-SDRAM-DDR2-800-PC2-6400-Dual-Chan-/300918732975 http://www.ebay.com/itm/Corsair-XMS2-4GB-DDR2-SDRAM-Memory-Module-TWIN2X4096-6400C5C-/261226077701 Edited by Anshad Edavana, 14 June 2013 - 11:46 PM. Then attempt to start up then stops. You could could buy them one by one but usually I go for the dual pack. How To Install Ram Bioshock. (Full Graphics) Stalker (High Graphics with no adaptive lighting) Timeshift (Full)      Cheers Wednesday, January 16, 2008 8:20 PM Reply | Quote 0 Sign in to vote Hehe, good

Once rebooted i turned OFF the Crossfire and shut the PC down. let me know and I will look at it. this is real life and a free forum... this content I ran memtest86 overnight, for just over 12 hours.

What I don't understand, even with generic, is how both new sticks of memory (not used or refurbished) could fail. It is better to find the faulty module and replace it with a compatible G-Skill module. It also doesn't make the chime it usually makes when I turn it on. johnblJan 25, 2014, 2:31 AM old BIOS are not too smart when I comes to adding new memory.

this way if windows resets your sata port it will auto reconnect and there will be a event log to show for it. (later you have to figure out why the I switched the DIMMS slots around to see if the slots were bad.